1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
|
##
## tinyproxy.conf -- tinyproxy daemon configuration file
##
#
# Name of the user the tinyproxy daemon should switch to after the port
# has been bound.
#
User nobody
Group nogroup
#
# Port to listen on.
#
Port 8888
#
# If you have multiple interfaces this allows you to bind to only one. If
# this is commented out, tinyproxy will bind to all interfaces present.
#
#Listen 192.168.0.1
#
# The Bind directive allows you to bind the outgoing connections to a
# particular IP address.
#
#Bind 192.168.0.1
#
# Timeout: The number of seconds of inactivity a connection is allowed to
# have before it closed by tinyproxy.
#
Timeout 600
#
# Where to log the information. Either LogFile or Syslog should be set,
# but not both.
#
Logfile "/var/log/tinyproxy.log"
# Syslog On
#
# Set the logging level. Allowed settings are:
# Critical (least verbose)
# Error
# Warning
# Notice
# Connect (to log connections without Info's noise)
# Info (most verbose)
# The LogLevel logs from the set level and above. For example, if the LogLevel
# was set to Warning, than all log messages from Warning to Critical would be
# output, but Notice and below would be suppressed.
#
LogLevel Info
#
# PidFile: Write the PID of the main tinyproxy thread to this file so it
# can be used for signalling purposes.
#
PidFile "/var/run/tinyproxy.pid"
#
# Include the X-Tinyproxy header, which has the client's IP address when
# connecting to the sites listed.
#
#XTinyproxy mydomain.com
#
# Turns tinyproxy into a TCP tunnel which connects the local computer on
# 'Port' to the remote computer's port. No processing is done when using
# tinyproxy as a tunnel. If you want to connect to an upstream proxy use
# the "Upstream" directive below.
#
#Tunnel some.remote.computer:port
#
# Turns on upstream proxy support.
#
#Upstream some.remote.proxy:port
#
# This is the absolute highest number of threads which will be created. In
# other words, only MaxClients number of clients can be connected at the
# same time.
#
MaxClients 100
#
# These settings set the upper and lower limit for the number of
# spare servers which should be available. If the number of spare servers
# falls below MinSpareServers then new ones will be created. If the number
# of servers exceeds MaxSpareServers then the extras will be killed off.
#
MinSpareServers 5
MaxSpareServers 20
#
# Number of servers to start initially.
#
StartServers 10
#
# MaxRequestsPerChild is the number of connections a thread will handle
# before it is killed. In practise this should be set to 0, which disables
# thread reaping. If you do notice problems with memory leakage, then set
# this to something like 10000
#
MaxRequestsPerChild 0
#
# The following is the authorization controls. If there are any access
# control keywords then the default action is to DENY. Otherwise, the
# default action is ALLOW.
#
# Also the order of the controls are important. The incoming connections
# are tested against the controls based on order.
#
Allow 127.0.0.1
Allow 192.168.1.0/25
#
# The location of the filter file.
#
#Filter "/etc/tinyproxy/filter"
#
# Filter based on URLs rather than domains.
#
#FilterURLs On
#
# Use POSIX Extended regular expressions rather than basic.
#
#FilterExtended On
#
# Change the default policy of the filtering system. If this directive is
# commented out, or is set to "No" then the default policy is to allow everything
# which is not specifically denied by the filter file.
#
# However, by setting this directive to "Yes" the default policy becomes to
# deny everything which is _not_ specifically allowed by the filter file.
#
#FilterDefaultDeny Yes
#
# If an Anonymous keyword is present, then anonymous proxying is enabled.
# The headers listed are allowed through, while all others are denied. If
# no Anonymous keyword is present, then all header are allowed through.
# You must include quotes around the headers.
#
#Anonymous "Host"
#Anonymous "Authorization"
#
# This is a list of ports allowed by tinyproxy when the CONNECT method
# is used. To disable the CONNECT method altogether, set the value to 0.
# If no ConnectPort line is found, all ports are allowed (which is not
# very secure.)
#
# The following two ports are used by SSL.
#
ConnectPort 443
ConnectPort 563
|
